doc::Smokeping::probes::TedlonceS:tm:IoSOkmSeoPPkiiennpggi(n3g)::probes::TelnetIOSPing(3)



NNAAMMEE
       Smokeping::probes::TelnetIOSPing - Cisco IOS Probe for
       SmokePing

SSYYNNOOPPSSIISS
        *** Probes ***

        +TelnetIOSPing

        forks = 5
        offset = 50%
        packetsize = 56
        step = 300
        timeout = 15

        # The following variables can be overridden in each target section
        iospass = password # mandatory
        iosuser = user # mandatory
        pings = 5
        psource = 192.168.2.129
        source = 192.168.2.1 # mandatory

        # [...]

        *** Targets ***

        probe = TelnetIOSPing # if this should be the default probe

        # [...]

        + mytarget
        # probe = TelnetIOSPing # if the default probe is something else
        host = my.host
        iospass = password # mandatory
        iosuser = user # mandatory
        pings = 5
        psource = 192.168.2.129
        source = 192.168.2.1 # mandatory

DDEESSCCRRIIPPTTIIOONN
       Integrates Cisco IOS as a probe into smokeping.  Uses the
       telnet protocol to run a ping from an IOS device (source)
       to another device (host).  This probe basically uses the
       "extended ping" of the Cisco IOS.  You have the option to
       specify which interface the ping is sourced from as well.

VVAARRIIAABBLLEESS
       Supported probe-specific variables:

       forks
           Run this many concurrent processes at maximum

           Example value: 5

           Default value: 5

       offset
           If you run many probes concurrently you may want to
           prevent them from hitting your network all at the same
           time. Using the probe-specific offset parameter you
           can change the point in time when each probe will be
           run. Offset is specified in % of total interval, or
           alternatively as 'random', and the offset from the
           'General' section is used if nothing is specified
           here. Note that this does NOT influence the rrds
           itself, it is just a matter of when data acqusition is
           initiated.  (This variable is only applicable if the
           variable 'concurrentprobes' is set in the 'General'
           section.)

           Example value: 50%

       packetsize
           The (optional) packetsize option lets you configure
           the packetsize for the pings sent.

           Default value: 56

       step
           Duration of the base interval that this probe should
           use, if different from the one specified in the
           'Database' section. Note that the step in the RRD
           files is fixed when they are originally generated, and
           if you change the step parameter afterwards, you'll
           have to delete the old RRD files or somehow convert
           them. (This variable is only applicable if the vari-
           able 'concurrentprobes' is set in the 'General' sec-
           tion.)

           Example value: 300

       timeout
           How long a single 'ping' takes at maximum

           Example value: 15

           Default value: 5

       Supported target-specific variables:

       iospass
           The iospass option allows you to specify the password
           for the username specified with the option iosuser.

           Example value: password

           This setting is mandatory.

       iosuser
           The iosuser option allows you to specify a username
           that has ping capability on the IOS Device.

           Example value: user

           This setting is mandatory.

       pings
           How many pings should be sent to each target, if dif-
           ferent from the global value specified in the Database
           section. Note that the number of pings in the RRD
           files is fixed when they are originally generated, and
           if you change this parameter afterwards, you'll have
           to delete the old RRD files or somehow convert them.

           Example value: 5

       psource
           The (optional) psource option specifies an alternate
           IP address or Interface from which you wish to source
           your pings from.  Routers can have many many IP
           addresses, and interfaces.  When you ping from a
           router you have the ability to choose which interface
           and/or which IP address the ping is sourced from.
           Specifying an IP/interface does not necessarily spec-
           ify the interface from which the ping will leave, but
           will specify which address the packet(s) appear to
           come from.  If this option is left out the IOS Device
           will source the packet automatically based on routing
           and/or metrics.  If this doesn't make sense to you
           then just leave it out.

           Example value: 192.168.2.129

       source
           The source option specifies the IOS device to which we
           telnet.  This is an IP address of an IOS Device that
           you/your server:      1)  Have the ability to telnet
           to      2)  Have a valid username and password for

           Example value: 192.168.2.1

           This setting is mandatory.

AAUUTTHHOORRSS
       John A Jackson <geonjay@infoave.net>

       based HEAVILY on Smokeping::probes::IOSPing by

       Paul J Murphy <paul@murph.org>

       based on Smokeping::probes::FPing by

       Tobias Oetiker <tobi@oetiker.ch>

NNOOTTEESS
       IIOOSS ccoonnffiigguurraattiioonn

       The IOS device should have a username/password configured,
       as well as the ability to connect to the VTY(s).  eg:

           !
           username smokeping privilege 5 password 0 SmokepingPassword
           !
           line vty 0 4
            login local
            transport input telnet
           !

       Some IOS devices have a maximum of 5 VTYs available, so be
       careful not to hit a limit with the 'forks' variable.

       RReeqquuiirreemmeennttss

       This module requires the Net::Telnet module for perl.
       This is usually included on most newer OSs which include
       perl.

       DDeebbuuggggiinngg

       There is some VERY rudimentary debugging code built into
       this module (it's based on the debugging code written into
       Net::Telnet).  It will log information into three files
       "TIPreturn", "TIPoutlog", and "TIPdump".  These files will
       be written out into your current working directory (CWD).
       You can change the names of these files to something with
       more meaning to you.

       PPaasssswwoorrdd aauutthheennttiiccaattiioonn

       You should be advised that the authentication method of
       telnet uses clear text transmissions...meaning that with-
       out proper network security measures someone could sniff
       your username and password off the network.  I may attempt
       to incorporate SSH in a future version of this module, but
       it is very doubtful.  Right now SSH adds a LOT of process-
       ing overhead to a router, and isn't incredibly easy to
       implement in perl.

       Having said this, don't be too scared of telnet.  Remem-
       ber, the original IOSPing module used RSH, which is even
       more scary to use from a security perspective.

       PPiinngg ppaacckkeett ssiizzee

       The FPing manpage has the following to say on the topic of
       ping packet size:

       Number of bytes of ping data to send.  The minimum size
       (normally 12) allows room for the data that fping needs to
       do its work (sequence number, timestamp).  The reported
       received data size includes the IP header (normally 20
       bytes) and ICMP header (8 bytes), so the minimum total
       size is 40 bytes.  Default is 56, as in ping. Maximum is
       the theoretical maximum IP datagram size (64K), though
       most systems limit this to a smaller, system-dependent
       number.



2.0.9                    doc2:0:0S6m-o0k7e-p1i4ng::probes::TelnetIOSPing(3)
