  SRM Firmware Howto
  David Mosberger <mailto:davidm@azstarnet.com>, Rich Payne
  <mailto:rdp@alphalinux.org>, and David Huggins-Daines
  <mailto:dhuggins@linuxcare.com>
  v0.6, 3 March 2000

  This document describes how to boot Linux/Alpha using the SRM console,
  which is the console firmware also used to boot Compaq Tru64 Unix
  (also known as Digital Unix and OSF/1) and OpenVMS.
  ______________________________________________________________________

  Table of Contents


  1. About this manual
     1.1 Who should read this manual
     1.2 Conventions

  2. What is SRM?
     2.1 Getting to SRM
     2.2 Using the SRM console
     2.3 How Does SRM Boot an OS?
     2.4 Loading The Secondary Bootstrap Loader

  3. The Raw Loader
  4. The aboot Loader
     4.1 Getting and Building aboot
     4.2 Floppy Installation
     4.3 Harddisk Installation
     4.4 CD-ROM Installation
     4.5 Building the Linux Kernel
     4.6 Booting Linux
	4.6.1 Device Naming
	4.6.2 Boot Filename
	4.6.3 Boot Flags
	4.6.4 Using aboot interactively
	4.6.5 The aboot.conf configuration file
	   4.6.5.1 Selecting the Partition of /etc/aboot.conf
     4.7 Installing Linux Distributions
	4.7.1 Installation from the Red Hat 6.0 CD
	4.7.2 Installation from the SuSE 6.1 CD
     4.8 Booting Over the Network
     4.9 Partitioning Disks
	4.9.1 What is a disklabel?
	4.9.2 Partitioning the Easy Way: a DOS Disklabel
	4.9.3 Partitioning with a BSD Disklabel

  5. Sharing a Disk With DEC Unix
     5.1 Partitioning the disk
     5.2 Installing aboot

  6. Document History


  ______________________________________________________________________

  1.  About this manual

  1.1.	Who should read this manual

  You should read this manual if you are installing Linux on a new Alpha
  system that can only boot from the SRM console, or if you are
  installing Linux on an older Alpha system that can use the SRM console
  and wish to use SRM to boot your Linux installation.


  Because SRM is the only way to boot Linux on modern Alpha systems, and
  because it provides the proper operating environment for Unix and
  Unix-like operating systems (such as Linux), it is the recommended way
  of booting Linux on Alpha when available.

  Sometimes, it is preferable to use the ARC, ARCSBIOS, or AlphaBIOS
  console, such as if you have a machine for which SRM is not available,
  if you wish to dual-boot with Windows NT without switching consoles,
  or if you have hardware that is not supported by SRM.	On these
  machines, you will typically use MILO to boot Linux.	For more
  information, refer to the MILO Howto, available from
  http://www.alphalinux.org/faq/milo.html
  <http://www.alphalinux.org/faq/milo.html>.

  1.2.	Conventions

  Throughout this manual, we will use the following conventions for
  commands to be entered by the user:

  SRM console commands will be shown with the characteristic SRM will
  see 'P00>' instead, or possibly some other number depending on which
  processor SRM is running.--)



       >>> boot dva0 -fi linux.gz -fl "root=/dev/fd0 load_ramdisk=1"



  Unix commands will be shown with the '#' command prompt if they are to
  be run as root, or '$' if they are to be run by a normal user, like
  this:


       # swriteboot -f3 /dev/sda /boot/bootlx



  Aboot commands will be shown with the 'aboot>' command prompt, like
  this:


       aboot> b 6/boot/vmlinuz root=/dev/hda6



  2.  What is SRM?

  SRM console is used by Alpha systems as Unix-style boot firmware.
  Tru64 Unix and OpenVMS depend on it and Linux can boot from it. You
  can recognize SRM console as a blue screen with a prompt that is
  presented to you on power-up.

  2.1.	Getting to SRM

  Most Alpha systems have both the SRM and ARC/AlphaBIOS console in
  their firmware.  On one of these machines, if your machine starts up
  with ARC/AlphaBIOS by default, you can switch to SRM through the
  "Console Selection" option in the Advanced CMOS Setup menu.  To make
  the change permanent, you should set the os_type environment variable
  in SRM to "OpenVMS" or "Unix", like this:


  >>> set os_type Unix



  Either one will work to boot Linux.  However, if you intend to dual-
  boot OpenVMS on this machine, you must set os_type to "OpenVMS".
  Conversely, to return to ARC/AlphaBIOS, you can set os_type to "NT".

  Some older systems may not have both SRM and ARC in firmware as
  shipped.  On these systems, you will have to upgrade your firmware.
  See  <http://ftp.digital.com/pub/DEC/Alpha/firmware/> for the latest
  firmware updates and instructions.

  A few older systems (primarily evaluation boards such as the 164SX and
  164LX) are "half-flash" systems, whose firmware can hold SRM or
  AlphaBIOS, but not both.  If you have one of these machines, you will
  have to reflash your firmware with the SRM console using the AlphaBIOS
  firmware update utility.  Again, see
  <http://ftp.digital.com/pub/DEC/Alpha/firmware/> for firmware images
  and instructions.  If you wish to return to AlphaBIOS on these
  machines, you may rerun the firmware update utility from a floppy in
  SRM using the fwupdate command.  You can also start AlphaBIOS from a
  floppy using the arc command.

  2.2.	Using the SRM console

  The SRM console works very much like a Unix or OpenVMS shell.	It
  views your NVRAM and devices as a pseudo-filesystem.	You can see this
  if you use the ls command.  Also, it contains a fairly large set of
  diagnostic, setup, and debugging utilities, the details of which are
  beyond the scope of this document.  As in the Unix shell, you can pipe
  the output of one command to the input of another, and there is a more
  command that works not unlike the Unix one.  To get a full listing of
  available commands, run:


       >>> help | more



  As well, SRM has environment variables, a number of which are pre-
  defined and correspond to locations in NVRAM.	You can view the entire
  list of environment variables and their values with the show command
  (there are quite a few of them, so you will probably want to pipe its
  output to more).  You can also show variables matching a "glob"
  pattern - for example, show boot* will show all the variables starting
  in "boot".

  Environment variables are categorized as either read-only, warm non-
  volatile, or cold non-volatile.  The full listing of pre-defined
  variables is detailed in the Alpha Architecture Reference Manual.  The
  most useful pre-defined environment variables for the purposes of
  booting Linux are BOOTDEF_DEV, BOOT_FILE, BOOT_FLAGS, and AUTO_ACTION,
  all of which are cold non-volatile.

  To set environment variables, use the set command, like this (unlike
  Unix environment variables, their names are case-insensitive):


       >>> set bootdef_dev dka0



  If you set an undefined variable, it will be created for you, however
  it will not persist across reboots.

  The BOOTDEF_DEV variable specifies the device (using VMS naming
  conventions - see ``'' for an explanation of these) which will be
  booted from if no device is specified on the boot command line, or in
  an automatic boot.  The BOOT_FILE variable contains the filename to be
  loaded by the secondary bootloader, while BOOT_FLAGS contains any
  extra flags.	AUTO_ACTION specifies the action which the console
  should take on power-up.  By default, it is set to HALT, meaning that
  the machine will start up in the SRM console.	Once you have
  configured your bootloader and the boot-related variables, you can set
  it to BOOT in order to boot automatically on power-up.

  Finally, two helpful console keystrokes you should know are Control-C,
  which, as in the shell, halts a command in progress (such as an
  automatic boot), and Control-P, which if issued from the aboot prompt
  (or other secondary bootloader) will halt the bootloader and return
  you to the SRM console.

  2.3.	How Does SRM Boot an OS?

  All versions of SRM can boot from SCSI disks and the versions for
  recent platforms, such as the Noname or AlphaStations can boot from
  floppy disks as well.	Network booting via bootp is supported.  Note
  that older SRM versions (notably the one for the Jensen) cannot boot
  from floppy disks. Booting from IDE devices is supported on newer
  platforms (DS20, DS10, DP264, UP2000 etc..).

  Booting Linux with SRM is a two step process: first, SRM loads and
  transfers control to the secondary bootstrap loader.	Then the
  secondary bootstrap loader sets up the environment for Linux, reads
  the kernel image from a disk filesystem and finally transfers control
  to Linux.

  Currently, there are two secondary bootstrap loaders for Linux: the
  raw loader that comes with the Linux kernel and aboot which is
  distributed separately.  These two loaders are described in more
  detail below.

  2.4.	Loading The Secondary Bootstrap Loader

  SRM knows nothing about filesystems or disk-partitions.  It simply
  expects that the secondary bootstrap loader occupies a consecutive
  range of physical disk sector, starting from a given offset.	The
  information on the size of the secondary bootstrap loader and the
  offset of its first disk sector is stored in the first 512 byte
  sector.  Specifically, the long integer at offset 480 stores the size
  of the secondary bootstrap loader (in 512-byte blocks) and the long at
  offset 488 gives the sector number at which the secondary bootstrap
  loader starts.  The first sector also stores a flag-word at offset 496
  which is always 0 and a checksum at offset 504.  The checksum is
  simply the sum of the first 63 long integers in the first sector.

  If the checksum in the first sector is correct, SRM goes ahead and
  reads the size sectors starting from the sector given in the sector
  number field and places them in virtual memory at address 0x20000000.
  If the reading completes successfully, SRM performs a jump to address
  0x20000000.

  3.  The Raw Loader

  The sources for this loader can be found in directory arch/alpha/boot
  of the Linux kernel source distribution.  It loads the Linux kernel by
  reading START_SIZE bytes starting at disk offset BOOT_SIZE+512 (also
  in bytes).  The constants START_SIZE and BOOT_SIZE are defined in
  linux/include/asm-alpha/system.h.  START_SIZE must be at least as big
  as the kernel image (i.e., the size of the .text, .data, and .bss
  segments).  Similarly, BOOT_SIZE must be at least as big as the image
  of the raw bootstrap loader.	Both constants should be an integer
  multiple of the sector size, which is 512 bytes.  The default values
  are currently 2MB for START_SIZE and 16KB for BOOT_SIZE.  Note that if
  you want to boot from a 1.44MB floppy disk, you have to reduce
  START_SIZE to 1400KB and make sure that the kernel you want to boot is
  no bigger than that.

  To build a raw loader, simply type make rawboot in the top directory
  of your linux source tree (typically /usr/src/linux).	This should
  produce the following files in arch/alpha/boot:


     tools/lxboot:
	The first sector on the disk.  It contains the offset and size
	of the next file in the format described above.

     tools/bootlx:
	The raw boot loader that will load the file below.

     vmlinux.nh:
	The raw kernel image consisting of the .text, .data, and .bss
	segments of the object file in /usr/src/linux/vmlinux.	The
	extension .nh indicates that this file has no object-file
	header.

  The concatenation of these three files should be written to the disk
  from which you want to boot.	For example, to boot from a floppy,
  insert an empty floppy disk in, say, /dev/fd0 and then type:


       # cat tools/lxboot tools/bootlx vmlinux >/dev/fd0



  You can then shutdown the system and boot from the floppy by issuing
  the command boot dva0.

  4.  The aboot Loader

  When using the SRM firmware, aboot is the preferred way of booting
  Linux.  It supports:


  o  direct booting from various filesystems (ext2, ISO9660, and UFS,
     the DEC Unix filesystem)

  o  listing directories and following symbolic links on ext2

  o  booting of executable object files (both ELF and ECOFF)

  o  booting compressed kernels

  o  network booting (using bootp)

  o  partition tables in DEC Unix format (which is compatible with BSD
     Unix partition tables)

  o  interactive booting and default configurations for SRM consoles
     that cannot pass long option strings



  4.1.	Getting and Building aboot

  The latest sources for aboot are available in this ftp directory
  <ftp://ftp.alphalinux.org.com/aboot>.	The description in this manual
  applies to aboot version 0.6 or newer. Please note that many
  distributions ship aboot with them so downloading aboot from this
  directory is probably unnessesary.

  Once you downloaded and extracted the latest tar file, take a look at
  the README and INSTALL files for installation hints.	In particular,
  be sure to adjust the variables in Makefile and in include/config.h to
  match your environment.  Normally, you won't need to change anything
  when building under Linux, but it is always a good idea to double
  check.  If you're satisfied with the configuration, simply type make
  to build it (if you're not building under Linux, be advised that aboot
  requires GNU make).

  After running make, the aboot directory should contain the following
  files:


     aboot
	This is the actual aboot executable (either an ECOFF or ELF
	object file).

     bootlx
	Same as above, but it contains only the text, data and bss
	segments---that is, this file is not an object file.

     sdisklabel/writeboot
	Utility to install aboot on a hard disk.

     tools/e2writeboot
	Utility to install aboot on an ext2 filesystem (usually used for
	floppies only).

     tools/isomarkboot
	Utility to install aboot on a iso9660 filesystem (used by CD-ROM
	distributors).

     tools/abootconf
	Utility to configure an installed aboot.

  4.2.	Floppy Installation

  The bootloader can be installed on a floppy using the e2writeboot
  command (note: this can't be done on a Jensen since its firmware does
  not support booting from floppy).  This command requires that the disk
  is not overly fragmented as it needs to find enough contiguous file
  blocks to store the entire aboot image (currently about 90KB).  If
  e2writeboot fails because of this, reformat the floppy and try again
  (e.g., with fdformat(1)).  For example, the following steps install
  aboot on floppy disk assuming the floppy is in drive /dev/fd0:


       # fdformat /dev/fd0
       # mke2fs /dev/fd0
       # e2writeboot /dev/fd0 bootlx



  4.3.	Harddisk Installation

  Since the e2writeboot command may fail on highly fragmented disks and
  since reformatting a harddisk is not without pain, it is generally
  safer to install aboot on a harddisk using the swriteboot command.
  swriteboot requires that the first few sectors are reserved for
  booting purposes.  We suggest that the disk be partitioned such that
  the first partition starts at an offset of 2048 sectors.  This leaves
  1MB of space for storing aboot.  On a properly partitioned disk, it is
  then possible to install aboot as follows (assuming the disk is
  /dev/sda):


       # swriteboot /dev/sda bootlx



  On systems where partition c in the entire disk it will be neccesary
  to 'force' the write of aboot. In this case use the -f flag followed
  by the partition number (in the case of parition c this is 3):


       # swriteboot /dev/sda bootlx -f3



  On a Jensen, you will want to leave some more space, since you need to
  write a kernel to this place, too---2MB should be sufficient when
  using compressed kernels.  Use swriteboot as described in Section ``''
  to write bootlx together with the Linux kernel.

  4.4.	CD-ROM Installation

  To make a CD-ROM bootable by SRM, simply build aboot as described
  above.  Then, make sure that the bootlx file is present on the iso9660
  filesystem (e.g., copy bootlx to the directory that is the filesystem
  master, then run mkisofs on that directory).	After that, all that
  remains to be done is to mark the filesystem as SRM bootable.	This is
  achieved with a command of the form:


       # isomarkboot filesystem bootlx



  The command above assumes that filesystem is a file containing the
  iso9660 filesystem and that bootlx has been copied into the root
  directory of that filesystem.	That's it!

  4.5.	Building the Linux Kernel

  A bootable Linux kernel can be built with the following steps.  During
  the make config, be sure to answer "yes" to the question whether you
  want to boot the kernel via SRM (for certain platforms this is
  automatically selected).  Note that if you build a generic kernel (by
  selecting "Generic" as the alpha system type), the kernel is able to
  guess whether it is running under SRM or not.


       # cd /usr/src/linux
       # make config
       # make dep
       # make boot
       # make modules (if applicable)
       # make modules_install (if applicable)


  The last command will build the file arch/alpha/boot/vmlinux.gz which
  can then be copied to the disk from which you want to boot from.  In
  our floppy disk example above, this would entail:


       # mount /dev/fd0 /mnt
       # cp arch/alpha/boot/vmlinux.gz /mnt
       # umount /mnt



  4.6.	Booting Linux

  With the SRM firmware and aboot installed, Linux is generally booted
  with a command of the form:

       >>> boot devicename -file filename -flags flags


  Note that -file and -flags can be abbreviated to -fi and -fl, and
  often are.

  The filename and flags arguments are optional; If they are not
  specified, SRM uses the default values stored in environment variables
  BOOTDEF_DEV , BOOT_OSFILE and BOOT_OSFLAGS.  The syntax and meaning of
  these two arguments is described in more detail below. To list the
  current values of these variables type show boot* at the SRM command
  prompt. This will also show a BOOT_DEV variable (among others), this
  variable is read only and needs to be changed via the BOOTDEF_DEV
  variable.

  4.6.1.  Device Naming

  This corresponds to the device from which SRM will attempt to boot.
  Examples include:


     dva0
	- First floppy drive, /dev/fd0 under Linux

     dqa0
	- Primary IDE cdrom or hard disk as Master, /dev/hda under Linux

     dqa1
	- Primary IDE cdrom or hard disk as Slave, /dev/hdb under Linux

     dka0
	- SCSI disk on first bus, Device 0, /dev/sda under Linux

     ewa0
	- First Ethernet Device, /dev/eth0 under Linux

  For example to boot from the disk at SCSI id 6, you would enter:


       >>> boot dka600



  To list the devices currently installed in the system type show dev at
  the SRM command line.	In contrast to Linux device naming, the
  partition number on a disk device is not given as part of the device
  name (you may see extra numbers after the device names when running
  show dev - these correspond to things like PCI bus and device numbers
  and are not useful to the user).  Remember, as mentioned in ``'', that
  SRM knows nothing about partitions or disklabels - it merely reads a
  boot block and secondary bootstrap from sectors on a disk.  Therefore,
  the partition number is given as part of the boot filename.

  4.6.2.  Boot Filename

  The filename argument takes the form:

       [n/]filename


  n is a single digit in the range 1..8 that gives the partition number
  from which to boot from.  filename is the path of the file you want
  boot.	For example to boot a kernel named vmlinux.gz from the second
  partition of SCSI device 6, you would enter:


       >>> boot dka600 -file 2/vmlinux.gz



  Or to boot from floppy drive 0, you'd enter:


       >>> boot dva0 -file vmlinux.gz



  If a disk has no partition table, aboot pretends the disk contains one
  ext2 partition starting at the first diskblock.  This allows booting
  from floppy disks.

  As a special case, partition number 0 is used to request booting from
  a disk that does not (yet) contain a file system.  When specifying
  "partition" number 0, aboot assumes that the Linux kernel is stored
  right behind the aboot image.	Such a layout can be achieved with the
  swriteboot command.  For example, to setup a filesystem-less boot from
  /dev/sda, one could use the command:


       # swriteboot /dev/sda bootlx vmlinux.gz



  Booting a system in this way is not normally necessary.  The reason
  this feature exists is to make it possible to get Linux installed on a
  systems that can't boot from a floppy disk (e.g., the Jensen).

  4.6.3.  Boot Flags

  A number of bootflags can be specified.  The syntax is:


       -flags "options..."



  Where "options..." is any combination the following options (separated
  by blanks).  There are many more bootoptions, depending on what
  drivers your kernel has installed.  The options listed below are
  therefore just examples to illustrate the general idea:
     load_ramdisk=1
	Copy root file system from a (floppy) disk to the RAM disk
	before starting the system.  The RAM disk will be used in lieu
	of the root device.  This is useful to bootstrap Linux on a
	system with only one floppy drive.

     floppy=str
	Sets floppy configuration to str.

     root=dev
	Select device dev as the root-file system. The device can be
	specified as a major/minor hex number (e.g., 0x802 for
	/dev/sda2) or one of a few canonical names (e.g., /dev/fd0,
	/dev/sda2).

     single
	Boot system in single user mode.

     kgdb
	Enable kernel-gdb (works only if CONFIG_KGDB is enabled; a
	second Alpha system needs to be connected over the serial port
	in order to make this work)

  Some SRM implementations (e.g., the one for the Jensen) are
  handicapped and allow only short option strings (e.g., at most 8
  characters).	In such a case, aboot can be booted with the single-
  character boot flag "i".  With this flag, aboot will enter interactive
  mode

  4.6.4.  Using aboot interactively

  As of version 0.6, aboot supports a simple command-oriented
  interactive mode.  Note that this is different from the prompt which
  previous versions issued when booted with the "i" flag, or after
  failing to load a kernel.  You can get a summary of the available
  commands by typing "h" or "?" at the prompt:


       >>> boot dka0 -fl i
       aboot> ?
	h, ?		   Display this message
	q		      Halt the system and return to SRM
	p 1-8		  Look in partition <num> for configuration/kernel
	l		      List preconfigured kernels
	d <dir>		List directory <dir> in current filesystem
	b <file> <args>	Boot kernel in <file> (- for raw boot)
			       with arguments <args>
	0-9		    Boot preconfiguration 0-9 (list with 'l')
       aboot> b 3/vmlinux.gz root=/dev/sda3 single



  4.6.5.  The aboot.conf configuration file

  Since booting in that manner quickly becomes tedious, aboot allows to
  define short-hands for frequently used commandlines.	In particular, a
  single digit option (0-9) requests that aboot uses the corresponding
  option string stored in file /etc/aboot.conf.	A sample aboot.conf is
  shown below:



  #
  # aboot default configurations
  #
  0:3/vmlinux.gz root=/dev/sda3
  1:3/vmlinux.gz root=/dev/sda3 single
  2:3/vmlinux.new.gz root=/dev/sda3
  3:3/vmlinux root=/dev/sda3
  8:- root=/dev/sda3		# fs-less boot of raw kernel
  9:0/vmlinux.gz root=/dev/sda3 # fs-less boot of (compressed) ECOFF kernel
  -



  With this configuration file, the command


       >>> boot dka0 -fl 1



  corresponds exactly to the boot command shown above.

  Finally, at the aboot prompt, it is possible to enter one of the
  single character flags ("0"-"9") to get the same effect as if that
  flag had been specified in the boot command line.  As noted in the
  help text cited above, you can also list the available default
  configurations with the "l" command.

  4.6.5.1.  Selecting the Partition of /etc/aboot.conf

  When installed on a harddisk, aboot needs to know what partition to
  search for the /etc/aboot.conf file.	A newly compiled aboot will
  search the second partition (e.g., /dev/sda2).  Since it would be
  inconvenient to have to recompile aboot just to change the partition
  number, abootconf allows to directly modify an installed aboot.
  Specifically, if you want to change aboot to use the third partition
  on disk /dev/sda, you'd use the command:


       # abootconf /dev/sda 3



  You can verify the current setting by simply omitting the partition
  number.  That is: abootconf /dev/sda will print the currently selected
  partition number.  Note that aboot does have to be installed already
  for this command to succeed.	As of version 0.6, swriteboot will
  preserve the existing configuration when installing a new aboot on a
  hard disk.

  Since aboot version 0.5, it is also possible to select the aboot.conf
  partition via the boot command line. This can be done with a command
  line of the form a:b where a is the partition that holds
  /etc/aboot.conf and b is a single-letter option as described above
  (0-9, i, or h). For example, if you type boot -fl "3:h" dka100 the
  system boots from SCSI ID 1, loads /etc/aboot.conf from the third
  partition, prints its contents on the screen and waits for you to
  enter the boot options.

  4.7.	Installing Linux Distributions



  4.7.1.  Installation from the Red Hat 6.0 CD

  Red Hat have made their distribution CD bootable from SRM console (--
  Please note that through the official RedHat CD-ROM is SRM bootable,
  copies made by various other companies may not be bootable.--)

  To start an installation, put the CD in and type the following:


       >>> boot srm-device -file kernels/generic.gz -flags root=linux-device



  In the above, the SRM device name and Linux device name for your CD-
  ROM drive are needed.	For Example if the machine had an IDE cdrom
  installed as primary master the command would look like this:


       >>> boot dqa0 -file kernels/generic.gz -flags "root=/dev/hda"



  See the section on ``'' conventions if you don't know what these are.

  4.7.2.  Installation from the SuSE 6.1 CD

  The SuSE 6.1 CD is not bootable from SRM console. SuSE have an
  alternative approach which involves creating two boot floppies, the
  images of which are included on the CD.  The boot disks can be created
  in various ways, depending on the systems you have available

  Writing the boot disks from a linux system The command to use is dd.
  From the mount-point of SuSE CD 1, the commands are:


       # dd if=disks/aboot of=/dev/fd0
       # dd if=disks/install of=/dev/fd0



  For writing the boot disks from a windows system, the command to use
  is rawrite. It is available on the CD.



       D:\tools\> rawrite



  The program then prompts for input disk image and output disk drive.
  Run this command once for each of the disk images as shown above.

  Starting the SuSE installer from the boot disks With the floppy disk
  made from the aboot image in place, type:


       >>> boot dva0 -file vmlinux.gz -flags "root=/dev/fd0 load_ramdisk=1"



  This will start the kernel, prompt you for the second boot disk, and
  start the installer

  4.8.	Booting Over the Network

  Two preliminary steps are necessary before Linux can be booted via a
  network.  First, you need to set the SRM environment variables to
  enable booting via the bootp protocol and second you need to setup
  another machine as the your boot server.  Please refer to the SRM
  documentation that came with your machine for information on how to
  enable bootp.	Setting up the boot server is obviously dependent on
  what operating system that machine is running, but typically it
  involves starting the program bootpd in the background after
  configuring the /etc/bootptab file.  The bootptab file has one entry
  describing each client that is allowed to boot from the server.  For
  example, if you want to boot the machine myhost.cs.arizona.edu, then
  an entry of the following form would be needed:


       myhost.cs.arizona.edu:\
	       :hd=/remote/:bf=vmlinux.bootp:\
	       :ht=ethernet:ha=08012B1C51F8:hn:vm=rfc1048:\
	       :ip=192.12.69.254:bs=auto:



  This entry assumes that the machine's Ethernet address is 08012B1C51F8
  and that its IP address is 192.12.69.254.  The Ethernet address can be
  found with the show device command of the SRM console or, if Linux is
  running, with the ifconfig command.  The entry also defines that if
  the client does not specify otherwise, the file that will be booted is
  vmlinux.bootp in directory /remote.  For more information on
  configuring bootpd, please refer to its man page.

  Next, build aboot with with the command make netboot.	Make sure the
  kernel that you want to boot has been built already.	By default, the
  aboot Makefile uses the kernel in
  /usr/src/linux/arch/alpha/boot/vmlinux.gz (edit the Makefile if you
  want to use a different path).  The result of make netboot is a file
  called vmlinux.bootp which contains aboot and the Linux kernel, ready
  for network booting.

  Finally, copy vmlinux.bootp to the bootsever's directory.  In the
  example above, you'd copy it into /remote/vmlinux.bootp.  Next, power
  up the client machine and boot it, specifying the Ethernet adapter as
  the boot device.  Typically, SRM calls the first Ethernet adapter
  ewa0, so to boot from that device, you'd use the command:


       >>> boot ewa0



  The -fi and -fl options can be used as usual.	In particular, you can
  ask aboot to prompt for Linux kernel arguments by specifying the
  option -fl i.

  4.9.	Partitioning Disks

  4.9.1.  What is a disklabel?

  A disk label is a partition table. Unfortunately, there are several
  formats the partition table can take, depending on the operating
  system.
  DOS partition tables are the standard used by Linux and Windows.
  AlphaBIOS systems and every Linux kernel can read DOS partition
  tables. Unfortunately, the SRM console's boot sector format overlaps
  with parts of the DOS partition table on disk, and therefore DOS
  partition tables cannot be used with SRM.

  BSD disklabels are used by several variants of Unix, including Tru64.
  SRM's boot block does not conflict with the BSD disklabel (in fact,
  the BSD disklabel resides entirely within "reserved" areas of the
  first sector), and Linux can use a BSD disklabel, provided that
  support for BSD disklabels ahs been compiled into the kernel.

  To boot from a disk using SRM, a BSD disklabel is required. If the
  disk is not a boot disk, the BSD disklabel is not required. A BSD
  disklabel can be created using fdisk, the standard Linux disk
  partitioning tool.

  4.9.2.  Partitioning the Easy Way: a DOS Disklabel

  The simplest way to partition your disk is to let your Linux installer
  do it for you, for example by using Red Hat's disk druid or fdisk.  On
  Red Hat 6.1, this will produce a valid BSD disklabel, but only if the
  disk in question previously contained one.  In most cases, this will
  produce a DOS disklabel.  It will be readable by Linux, but you will
  not be able to boot from it via SRM.	For this reason, you will
  probably want to create a BSD disklabel manually in order to boot
  Linux

  4.9.3.  Partitioning with a BSD Disklabel


  1. Start fdisk on the disk you're configuring

  2. Choose to make a BSD disklabel - option 'b' (newer versions of
     fdisk will detect existing BSD disklabels and automatically enter
     disklabel mode)

  3. You'll notice some things: Partitions are letters instead of
     numbers, from a-h Partition 'c' covers the whole of the disk. This
     is the convention, don't touch it.	While you can see it, note down
     the disk parameters as you'll use them more often than with the
     DOS-disklabel approach

  4. Creating a new partition uses the same procedure as the DOS-
     disklabel approach, except that the partitions are referred to by
     letter instead of number. That is, 'n' to make a new partition
     followed by the partition letter followed by the starting block
     followed by the end block

  5. Setting partition type is slightly different, because the numbering
     scheme is different (1 is swap, 8 is ext2).

  6. When you are finished, write ('w') and quit ('q') as normal.

  There are some important catches that you must be aware of when
  partitioning using a BSD disklabel:

  o  Partition 'a' should start about 1M into the disk: don't start it
     at sector 1, try starting at sector 10 (for example). This leaves
     plenty of space for writing the boot block (see below)

  o  There is a bug in some versions of fdisk which makes the disk look
     one sector bigger than it actually is.  The listing when you create
     the BSD disklabel is correct.  The last sector of partition 'c' is
     correct.  The default last sector when creating a new partition is
     1 sector too big
  o  Always adjust for this extra sector. This bug exists in the version
     of fdisk shipped with Red Hat 6.0. Not making an adjustment for
     this problem almost always leads to "Access beyond end of device"
     errors from the Linux kernel.

  Once you have made a BSD disklabel, continue the installation. After
  installation, you can write a boot block to your disk to make it
  bootable from SRM.

  5.  Sharing a Disk With DEC Unix

  Unfortunately, DEC Unix doesn't know anything about Linux, so sharing
  a single disk between the two OSes is not entirely trivial.  However,
  it is not a difficult task if you heed the tips in this section.  The
  section assumes you are using aboot version 0.5 or newer.

  5.1.	Partitioning the disk

  First and foremost: never use any of the Linux partitioning programs
  (minlabel or fdisk) on a disk that is also used by DEC Unix.	The
  Linux minlabel program uses the same partition table format as DEC
  Unix disklabel, but there are some incompatibilities in the data that
  minlabel fills in, so DEC Unix will simply refuse to accept a
  partition table generated by minlabel.  To setup a Linux ext2
  partition under DEC Unix, you'll have to change the disktab entry for
  your disk.  For the purpose of this discussion, let's assume that you
  have an rz26 disk (a common 1GB drive) on which you want to install
  Linux.  The disktab entry under DEC Unix v3.2 looks like this (see
  file /etc/disktab):


       rz26|RZ26|DEC RZ26 Winchester:\
	       :ty=winchester:dt=SCSI:ns#57:nt#14:nc#2570:\
	       :oa#0:pa#131072:ba#8192:fa#1024:\
	       :ob#131072:pb#262144:bb#8192:fb#1024:\
	       :oc#0:pc#2050860:bc#8192:fc#1024:\
	       :od#393216:pd#552548:bd#8192:fd#1024:\
	       :oe#945764:pe#552548:be#8192:fe#1024:\
	       :of#1498312:pf#552548:bf#8192:ff#1024:\
	       :og#393216:pg#819200:bg#8192:fg#1024:\
	       :oh#1212416:ph#838444:bh#8192:fh#1024:



  The interesting fields here are o?, and p?, where ? is a letter in the
  range a-h (first through 8-th partition).  The o value gives the
  starting offset of the partition (in sectors) and the p value gives
  the size of the partition (also in sectors).	See disktab(4) for more
  info.	Note that DEC Unix likes to define overlapping partitions.  For
  the entry above, the partition layout looks like this (you can verify
  this by adding up the various o and p values):


	 a     b	 d	   e		f
       |---|-------|-----------|-----------|-----------|

			       c
       |-----------------------------------------------|

			    g		 h
		   |-----------------|-----------------|



  DEC Unix insists that partition a starts at offset 0 and that
  partition c spans the entire disk.  Other than that, you can setup the
  partition table any way you like.

  Let's suppose you have DEC Unix using partition g and want to install
  Linux on partition h with partition b being a (largish) swap
  partition.  To get this layout without destroying the existing DEC
  Unix partition, you need to set the partition types explicitly.  You
  can do this by adding a t field for each partition.  In our case, we
  add the following line to the above disktab entry.


	       :ta=unused:tb=swap:tg=4.2BSD:th=resrvd8:



  Now why do we mark partition h as "reservd8" instead of "ext2"?  Well,
  DEC Unix doesn't know about Linux.  It so happens that partition type
  "ext2" corresponds to a numeric value of 8, and DEC Unix uses the
  string "reservd8" for that value.  Thus, in DEC Unix speak, "reservd8"
  means "ext2".	OK, this was the hard part.  Now we just need to
  install the updated disktab entry on the disk.  Let's assume the disk
  has SCSI id 5.  In this case, we'd do:


       # disklabel -rw /dev/rrz5c rz26



  You can verify that everything is all right by reading back the
  disklabel with disklabel -r /dev/rrz5c.  At this point, you may want
  to reboot DEC Unix and make sure the existing DEC Unix partition is
  still alive and well.	If that is the case, you can shut down the
  machine and start with the Linux installation.  Be sure to skip the
  disk partitioning step during the install.  Since we already installed
  a good partition table, you should be able to proceed and select the
  8th partition as the Linux root partition and the 2nd partition as the
  swap partition.  If the disk is, say, the second SCSI disk in the
  machine, then the device name for these partitions would be /dev/sdb8
  and /dev/sdb2, respectively (note that Linux uses letters to name the
  drives and numbers to name the partitions, which is exactly reversed
  from what DEC Unix does; the Linux scheme makes more sense, of course
  ;-).

  5.2.	Installing aboot

  First big caveat: with the SRM firmware, you can boot one and only one
  operating system per disk.  For this reason, it is generally best to
  have at least two SCSI disks in a machine that you want to dualboot
  between Linux and DEC Unix.  Of course, you could also boot Linux from
  a floppy if speed doesn't matter or over the network, if you have a
  bootp-capable server.	But in this section we assume you want to boot
  Linux from a disk that contains one or more DEC Unix partitions.

  Second big caveat: installing aboot on a disk shared with DEC Unix
  renders the first and third partition unusable (since those must have
  a starting offset of 0).  For this reason, we recommend that you
  change the size of partition a to something that is just big enough to
  hold aboot (1MB should be plenty).

  Once these two caveats are taken care of, installing aboot is almost
  as easy as usual: since partition a and c will overlap with aboot, we
  need to tell swriteboot that this is indeed OK.  We can do this under
  Linux with a command line of the following form (again, assuming we're
  trying to install aboot on the second SCSI disk):


       # swriteboot -f1 -f3 /dev/sdb bootlx



  The -f1 means that we want to force writing bootlx even though it
  overlaps with partition 1.  The corresponding applies for partition 3.

  This is it.  You should now be able to shutdown the system and boot
  Linux from the harddisk.  In our example, the SRM command line to do
  this would be:


       >>> boot dka5 -fi 8/vmlinux.gz -fl root=/dev/sdb8



  6.  Document History

  v0.6.1 6 March 2000 A few small fixes:

  o  Fixed some typos

  o  Use capitals consistently for SRM environment variables

  v0.6 3 March 2000 Changes and information from David Huggins-Daines
  <dhd@linuxcare.com>

  o  Moved the notes on MILO vs. SRM to an "About this document" section

  o  Added sections on switching to SRM, and basic SRM usage

  o  Added section on the new interactive use of aboot

  o  Updated the note on DOS partition tables to mention the Red Hat 6.1
     installer's behaviour.

  o  Normalized the markup, and codified the conventions used for user-
     entered commands.

  o  Corrected the notes on BSD disklabels (SRM does not read BSD
     disklabels, it's just that they don't conflict with the boot
     block).

  v0.5.2 5 December 1999 Added comments and information from Stig Telfer
  (stig @ alpha-processor.com).

  o  Added chart on SRM to Linux name mappings

  o  Added RedHat 6.0 and SuSE 6.1 installation information

  o  Added Disk Partitioning Information

  v0.5.1 (Not Released) 13 November 1999 Took the original 0.5 document
  and updated several parts:


  o  Update information on SRM booting from IDE devices

  o  Fixed URL to aboot source


  o  Update toc page to reflect MILO's future

  o  Included information on BOOTDEF_DEV and BOOT_DEV to chapter 3

  o  Added this section

  v0.5 17 August 1996 - Original Document by David Mosberger-Tang



