This has been contributed by Bruno Bonfils (asyd at debian-fr dot org)
Since I don't have enough computers to dedicate a box to GNU, I'm trying to do my own harddrive image disk. I thougt there was some documentation about how to do that. But since I didn't find anything and I decided to write a small doc. I hope this document will be useful for some people who wants to try the GNU/Hurd.
Debian (Sid) GNU/Linux 2.4.19 ii bochs 1.4.1.no.elpin IA-32 (x86) PC emulator ii bochs-x 1.4.1.no.elpin Bochs binary with X interface. ii grub 0.92+cvs200209 GRand Unified Bootloader ii gcc-i386-gnu 1.7-8 Cheap cross-compiler for GNU/Hurd. ii mig-i386-gnu 1.2-1 The GNU distribution of the Mach 3.0 interfaceIf you don't have time and if you trust me, you can download here [1] my own image file. (You don't need to run native-install)
![]() | In this example, I use a 112 MB image disk, but I think you can use any size without some problem. |
Use createdisk command like this :
# createdisk gnu.img 112 Disk Geometry: C: 227 H: 16 S: 63 Total size: 117153792 bytes
Note on a paper or on your memory the disk geometry. Then, use the losetup command to create a loopback on the whole disk.
# losetup /dev/loop1 gnu.img
Now, call fdisk on /dev/loop1. Go into expert mode, and modify the disk geometry using the c, h, s commands. Return in normal mode, and create an unique primary partition which uses the whole disk. Then, detach the /dev/loop1 using :
# losetup -d /dev/loop1
Attach the partition
First of all, you need to create a filesystem on the disk. Use the command losetup and -o <offset> option to attach /dev/loop1 on the first partition of an image disk. Offset is computed like this :
offset = sector * block_size (512)
# losetup -o 32256 /dev/loop1 gnu.img
Preparing the filesystem
According to the GNU/Hurd Installation Guide [2] , use mke2fs to create a filesystem.
# mke2fs -o hurd /dev/loop1Just mount /dev/loop1 like a typical dev.
# mount /dev/loop1 /mnt/gnu
Finish the installation
Download a GNU archive as indicated in the Hurd Installation Guide, and decompress it in /mnt/gnu.
# cd /mnt/gnu # tar --same-owner -xvzpf ~/gnu-latest.tar.gz
Copy default configuration (/usr/share/doc/bochs/examples/bochsrc.gz on debian) on your home directory and edit it with your favorite editor (GNU Emacs, i hope ;).
For my image file I have the following configuration :
romimage: file=/usr/share/bochs/BIOS-bochs-latest, address=0xf0000 megs: 128 vgaromimage: file=/usr/share/bochs/VGABIOS-lgpl-latest floppya: 1_44=/dev/fd0, status=ejected ata0-master: type=disk, path="/home/asyd/travail/hurd/gnu.img", cylinders=227, heads=16, spt=63 # edit me ata0-slave: type=cdrom, path=/dev/cdrom, status=inserted boot: disk log: /dev/stdout panic: action=ask error: action=report info: action=report debug: action=ignore vga_update_interval: 300000 keyboard_serial_delay: 250 keyboard_paste_delay: 100000 floppy_command_delay: 500 ips: 1000000 mouse: enabled=0 private_colormap: enabled=0 fullscreen: enabled=0 screenmode: name="sample" ne2k: ioaddr=0x280, irq=9, mac=fe:fd:00:00:00:01, ethmod=tap, ethdev=tap0 keyboard_mapping: enabled=0, map= keyboard_type: xt i440fxsupport: enabled=0note most of them are actually in the default Debian example file. If you use these lines, don't forget to read the Networking section.
Remember that the Hurd is not a kernel, it's just a collection of libraries and programs, so we can't actually boot the Hurd. We boot GNU Mach, and then launch the base servers.
The default GNU Mach which is provided by the default GNU archive contains some modules / drivers which are not needed in bochs environment. If you use it, you'll probably have some kernel panic while booting. Don't be afraid and just say alwayscont.
![]() | in my archive, I use a recompiled GNU Mach which contains only the drivers which are needed (--enable-floppy --enable-ide --enable-kmsg --enable-ne2000). If you want more informations on how to compile your own GNU Mach, just send me a mail and I'll add the section in this document. |
Create a grub floppy disk or use my floppy image [3] Adapt your bochsrc file according to your choice. If you want install Grub on the image disk, remember to copy stage1, stage2 Grub's files into /mnt/gnu/boot/grub.
Launch bochs - as root if you want networking (using sudo for example).
If you have stage1 and stage2 file, you can install Grub on the MBR.
<grub> root (hd0,0) <grub> setup (hd0)
Finally, booting GNU mach
<grub> root (hd0,0) <grub> kernel /boot/gnumach.gz root=hd0s1 <grub> module /boot/serverboot.gz <grub> bootNow, you can read the official GNU/Hurd Installation Guide [4] .
You can try to test networking between the GNU/Linux (host OS) and the GNU/Hurd. First of all, please read [5] , I currently have the *same* problem. [6]
Verify your kernel configuration, you need to have :
CONFIG_NETLINK_DEV=m CONFIG_ETHERTAP=m(or y instead or m). Check if /dev/tap0 file exist, else create it with
# mknod /dev/tap0 c 36 16and run this command on the guest os :
# ifconfig tap0 192.168.100.1 netmask 255.255.255.0Use ip 196.168.100.10 on the GNU/Hurd and you can ping 192.168.100.1
Mmenal
#hurdfr, #hurd, #bochs channels (Freenode network)
All people who help me everyday on IRC
Copyright (c) Bruno Bonfils
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.1 or any later version published by the Free Software Foundation.
[1] | |
[2] | |
[3] | Grub Floppy image : (coming soon) |
[4] | |
[5] | |
[6] | This can be solved by using the tuntap interface (see Section 8.10) |